Key takeaways
- Compare the best bench dogs for woodworking by hole size, material and pack count, from nylon stops and brakes to aluminum dogs and clamping models.
- Top Pick: POWERTEC 71500 Deluxe Bench Dogs, 8-Pack
- Runner-up: Kreg KKS1070 Bench Dogs
- Also consider: Taytools 468631 Bench Dogs, Pack of 4
Bench dogs are the small pegs that turn a row of holes in a workbench top into a flexible workholding system. Drop them into the dog holes, butt a board against them, and you have a stop for planing, routing, sanding, and cutting that can be repositioned in seconds. Paired with a tail vise or a bench dog clamp, they hold stock firmly without the setup time of bar clamps, and most designs sit low enough for tools to pass over them.
The catch is fit. Nearly every dog here is made for the standard 3/4-inch (19 mm) hole found on most North American benches, but materials and formats vary widely, from molded nylon stops with rubber brake pads to machined aluminum dogs with side springs and clamping models that pull a workpiece tight. Below are five current options, compared on hole size, material, and pack count.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
For most benches with 3/4-inch dog holes, the POWERTEC 71500 8-pack is the easy starting point: nylon dogs with removable EVA brake inserts. Choose the Kreg KKS1070 set if you want matched rubber bench brakes, the Taytools 468631 four-pack for machined aluminum dogs with side springs, the EWORK clamp pair when a plain stop is not enough, and the EZTOOL six-pack for aluminum stops.
POWERTEC 71500 Deluxe Bench Dogs, 8-Pack
POWERTEC’s 71500 set is the straightforward way to fill a row of dog holes. Each dog is molded from durable nylon with a 2-inch length, sized to press into a standard 3/4-inch (19 mm) hole. One side is squared to act as a flat clamping pad, while the other side is curved, so the same dog can register against straight edges or irregular stock. The top of each dog carries a removable bench brake insert of nonslip EVA rubber, adding grip for routing and sanding without marring finished surfaces.
A thoughtful extra is the pair of 3/16-inch holes in each dog, which accept dowels to create painter’s points for finishing work, and the orange and yellow colors are easy to spot in a pile of offcuts. As a plain stop with a padded face, this is a budget-tier set aimed at general bench work rather than heavy clamping, and the eight-piece count is enough to line up stops along a long board.
Specs
- Hole size: 3/4 inch (19 mm)
- Material: Nylon with EVA rubber brake inserts
- Dog length: 2 inches
- Pack count: 8 dogs
- Model: POWERTEC 71500
- Tier: Budget
Kreg KKS1070 Bench Dogs
Kreg’s KKS1070 set pairs each dog with a separate bench brake, which makes it a tidy kit for anyone who does a lot of routing and sanding at the bench. The dogs themselves are molded from reinforced nylon and sized for 3/4-inch dog holes. The included bench brakes are solid rubber pads that sit on top of the dogs, raising the workpiece slightly and giving it a non-slip surface to rest on while you work across a panel.
Because the brake is a separate piece, you can run the dogs bare as hard stops for planing or add the brakes when the job calls for grip instead of a positive edge. The set includes four dogs and four brakes, so it covers a typical four-hole layout along one edge of a bench. The 3/4-inch sizing means the dogs also work in any bench drilled to the same standard, not just Kreg benches.
Specs
- Hole size: 3/4 inch (19 mm)
- Material: Reinforced nylon dogs, solid rubber bench brakes
- Pack count: 4 dogs and 4 bench brakes
- Model: Kreg KKS1070
- Tier: Mid-range
Taytools 468631 Bench Dogs, Pack of 4
Taytools, the house brand of Taylor Toolworks, machines its 468631 bench dogs from anodized aluminum, which puts them at the premium end of this group. The shank of each dog is turned just under 3/4 inch in diameter, a deliberate choice so the dogs slide in and out of 3/4-inch holes without jamming, even as humidity swells a wooden bench top.
The defining feature is the side spring fitted to each dog. The spring presses against the wall of the hole and holds the dog at whatever height you set, rather than letting it drop flush or fall through. That makes these dogs useful as adjustable stops for thin stock, or lowered out of the way when you need a clear bench. The trade-off of an aluminum face is that it is harder than nylon or rubber, so care is needed against finished surfaces. The pack includes four dogs, which suits a single row of holes or a pair of stops at each end of a board.
Specs
- Hole size: 3/4 inch (19 mm), machined slightly undersize
- Material: Anodized aluminum with side springs
- Pack count: 4 dogs
- Model: Taytools 468631
- Tier: Premium
EWORK Bench Dog Clamp, 2-Pack
The EWORK bench dog clamp goes a step beyond a passive stop. Each unit drops into a 3/4-inch (19 mm) dog hole and uses a quick clamping and release design to pull the workpiece tight against the dog, with a maker-stated clamping force of up to 155 lbs. The body combines nylon with 45# steel components, a step up in rigidity from an all-plastic clamp.
This is the pick for jobs where a board wants to creep under a router or sander and a plain stop cannot hold it back. The two-pack format lets you clamp at two points along an edge, and the quick-release action keeps repositioning fast when you work through a batch of similar parts. The listing states a 2-year warranty. As a mid-range option, it fills the gap between simple peg stops and a full vise-and-dog setup.
Specs
- Hole size: 3/4 inch (19 mm)
- Material: Nylon and 45# steel
- Clamping force: Up to 155 lbs (maker-stated)
- Pack count: 2 clamps
- Model: EWORK EK-192DX
- Tier: Mid-range
EZTOOL 6-Pack Aluminum Bench Dogs
EZTOOL’s six-pack covers the middle ground between nylon stops and machined premium dogs. Each dog is cast from aluminum alloy in a low-profile bench brake style, sized for 3/4-inch (19 mm) dog holes, and finished in red. The wide, flat top face gives stock a broad surface to register against, and the aluminum body will not flex the way a thin plastic dog can under hard planing pressure.
With six dogs in the pack, you can set up a long stop line for panel work or split the set between two benches. There are no pads or springs in this design, so the metal face contacts the workpiece directly; for finished surfaces, a layer of tape or a shop-made pad is a sensible precaution. This is a budget-tier way to get metal dogs in quantity, suited to MFT-style tops and traditional benches alike.
Specs
- Hole size: 3/4 inch (19 mm)
- Material: Aluminum alloy
- Pack count: 6 dogs
- Part number: CCX002319R6PC
- Tier: Budget
How to choose bench dogs
Start with hole diameter, because nothing else matters if the dog does not fit. Measure the actual holes in your bench top rather than trusting the bench maker’s description. The long-running standard is 3/4 inch (19 mm), and every pick in this roundup is built for it. Many European-style MFT tops use 20 mm holes instead, and those need their own dogs; a 19 mm dog in a 20 mm hole will wobble, and a 20 mm dog will not enter a 3/4-inch hole at all. A few benches, such as Sjöbergs models, use 1-inch holes and their own accessories.
Next, decide between plain stops and clamping dogs. Plain dogs, like the POWERTEC, Kreg, Taytools, and EZTOOL sets here, act as fences: the workpiece rests against them and pressure from a plane, router, or sander keeps it in place, often helped by a tail vise at the other end. Bench dog clamps, like the EWORK pair, add a mechanism that actively pulls and holds the stock, which suits routing and sanding jobs where the work tends to skate.
Material sets the balance between kindness to the workpiece and durability. Nylon dogs and rubber brake pads are the gentlest on finished wood and are the budget-friendly option, while aluminum dogs are stiffer and longer-wearing but can mark soft or finished surfaces. Finally, match pack count to your bench: four dogs cover basic stops, while eight or more let you build a long stop line.
Who should skip bench dogs
Skip this category if your bench top has no dog holes and you do not plan to drill any; a face vise or surface clamps will serve you better. Owners of 20 mm MFT tops should also pass on the five picks here, since all of them are 3/4-inch designs, and shop for 20 mm dogs made for their table instead. If your work is mostly heavy mortising or aggressive planing of wide, rough boards, small bench stops may not hold firmly enough on their own, and a tail vise with steel dogs or a full clamping setup is the better investment. And if you rarely work at a bench at all, a portable work table with built-in clamping may be the simpler answer.
FAQ
What size bench dogs fit a standard workbench?
Most benches use 3/4-inch (19 mm) dog holes, and all five products in this roundup are made for that size. Some MFT-style tops use 20 mm holes and a few benches use 1-inch holes, so measure your bench before ordering rather than assuming the standard.
What is the difference between a bench dog and a bench dog clamp?
A bench dog is a passive stop: it sits in a hole and the workpiece rests against it. A bench dog clamp, such as the EWORK model above, adds a screw or quick-action mechanism that pulls the workpiece tight against the dog, which helps when routing or sanding makes stock want to move.
Can bench dogs damage a workpiece?
They can if a hard metal face is pressed against finished wood. Nylon dogs and rubber bench brakes, like the pads in the POWERTEC and Kreg sets, are the safer choice for finished surfaces. With aluminum dogs, a strip of tape or a thin shop-made pad between the dog and the work prevents marks.
How many bench dogs do I need?
Four dogs cover the basics: a pair of stops for short boards or a single stop line for longer ones. If you plane long panels or work at two surfaces, a larger pack such as the eight-piece POWERTEC set saves buying twice.
Final verdict
Bench dogs are a small purchase that changes how a bench works every day, and the right set depends on your holes and your habits. The POWERTEC 71500 8-pack is the best default for most shops: inexpensive nylon dogs with brake inserts that cover stops, sanding grip, and painter’s points in one box. The Kreg KKS1070 set is the cleaner choice when matched rubber brakes are the priority, the Taytools 468631 dogs reward anyone who wants machined aluminum with height-holding springs, the EWORK clamps answer the jobs where a stop alone lets stock creep, and the EZTOOL six-pack delivers simple metal stops in useful quantity. Measure your holes first, and any of these five will earn its place in the bench.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!