Key takeaways
- Refresh the push stick station with label staples, a 20 piece hex bit set, a small parts kit case, a soft dusting brush, and two spray bottles.
- Top Pick: Arrow 259 T25 Staples, 1100 count
- Runner-up: toolant Impact Allen Wrench Bit Set, 20 pc
- Also consider: Anvin Acoustic Guitar Accessories Kit
Every table saw station has a spot where the push sticks live, and that spot slowly falls apart in ways nobody schedules time to fix. The labels stapled to the station board fade until the fence settings written on them are guesswork. The hex bolts on the jig hardware work loose a quarter turn at a time. Small screws, washers, and spare parts migrate into a dusty pile in the corner of the bench. The wipe-down that should happen after a dusty session gets skipped because the spray bottle is empty, missing, or three rooms away.
A station reset is the short, deliberate version of fixing all of that at once. It is not a tool upgrade and it does not change how the saw cuts. It is one pass that restocks the consumables, tightens the hardware, corrals the small parts, and cleans the surfaces around the push sticks so the station is readable and tidy again. The five picks below are the supporting supplies for that pass. None of them is a push stick, and none of them is presented as one.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
None of these five picks is a push stick, and none replaces one at the blade. This reset refreshes the station around the sticks: staples for fresh labels, a hex bit set for loose jig bolts, a small kit case for loose hardware, a soft brush for dry dusting, and two small spray bottles for the wipe-down.
Arrow 259 T25 Staples, 1100 count
Station labels only stay useful if they get replaced when they fade, and staples are what hold most shop-made labels, setup cards, and blade-change logs to the board. The Arrow 259 is a box of T25 staples, the wire-style staple commonly used with T25 staple guns and tackers for fastening light material to wood. A reset pass typically burns through more staples than expected: old cards come down, new fence-position cards go up, a fresh blade log sheet replaces the coffee-stained one, and the push stick inventory list gets reprinted and reposted.
The count matters here. With 1,100 staples in the box, the reset does not stall halfway because the staple strip ran out, and there is enough left over for the smaller labeling jobs that come up between resets, like tagging a new jig or posting a sharpening schedule. These are consumables in the plainest sense, and treating them as a restock item rather than a permanent fixture is the right frame.
Specs
- Product type: T25 staples
- Count: 1,100 staples per box
- Leg length and crown width: not stated, confirm on the listing
- Compatible staple guns: T25-style guns and tackers, confirm fit on the listing
- Material: not stated
toolant Impact Allen Wrench Bit Set, 20 pc
Loose hardware is the quiet failure mode of a saw station. Fence locks, jig stops, featherboard mounts, and blade guard brackets all depend on hex socket bolts, and those bolts back out slowly under vibration. A reset pass includes putting a hex bit on every one of them and checking snugness, which is exactly the job a 20 piece Allen wrench bit set is built for. The bits load into a standard driver or impact driver, so the check goes bolt to bolt without swapping hand keys.
The toolant set is impact rated according to its product name, which suits the driver most shops already keep at the bench. Twenty pieces give a spread of hex sizes for the mix of hardware a station accumulates over years of jigs and accessories. A fair limitation: a bit set only covers hex socket fasteners. Stations held together with Phillips, Torx, or slotted hardware need those drivers too, and this set does not replace them. It also does not include the driver itself.
Specs
- Product type: Allen (hex) wrench bit set
- Piece count: 20 pieces
- Rating: impact rated per the product name
- Shank size and included hex sizes: not stated, confirm on the listing
- Storage case included: not stated
- Driver included: no, bits only
Anvin Acoustic Guitar Accessories Kit
This pick needs an honest introduction: the Anvin kit is an acoustic guitar accessories kit, not a woodworking product, and nothing in it is a shop tool. Its role in a station reset is narrower and simpler. Kits like this ship as a bundle of small accessories in a compact package, and a reset pass always turns up a scatter of small loose items at the station: spare bolts, washers, a stray insert, small parts waiting for a home. A small kit case is a reasonable corral for that scatter so the bench corner stops being the storage system.
That framing comes with clear limits. The accessories inside are guitar accessories, chosen for guitar players, and a woodworker who does not play guitar is buying this for the containment value, not the contents. Anyone who needs a dedicated small-parts organizer with divided compartments should buy that instead, because this kit is not one. It earns its place here only as a compact small-item holder that keeps loose hardware gathered in one spot at the station instead of spread across the bench.
Specs
- Product type: acoustic guitar accessories kit
- Intended use per the listing: guitar accessories bundle
- Exact contents: not stated here, confirm on the listing
- Case or pouch included: confirm on the listing
- Workshop rating: none, this is not a shop tool
LiBa Scalp Massager Shampoo Brush
Another honest framing: this is a scalp massager shampoo brush, a personal care product with soft silicone bristles, sold for use in the shower. In the shop, its only job is dry dusting. The soft bristles sweep sawdust out of the corners of the station, off the label board, and out of the texture of a work surface without scratching anything, and the compact shape fits into the tight spots around fence rails and miter slots where a bench brush is clumsy.
Two boundaries matter. First, this brush is a cleaning accessory for a powered-down, idle station during a reset, used on surfaces, never on the saw while it runs and never anywhere near a blade. Second, it is not a push stick, not a featherboard, and not a safety device of any kind, and it should never be used to move stock or clear offcuts. Within those limits, a soft silicone brush is a gentle dusting tool that will not mar the surfaces it cleans, and it rinses clean afterward, which a bristle bench brush does not.
Specs
- Product type: scalp massager shampoo brush
- Bristle material: silicone per the product category, confirm on the listing
- Intended use per the listing: scalp massage and shampoo brushing
- Dimensions and weight: not stated, confirm on the listing
- Shop safety rating: none, not a safety device
RELANOR Small Spray Bottle 2oz, 2 pack
The wipe-down step of a reset fails when the spray bottle is missing, so the fix is small bottles that live at the station permanently. The RELANOR bottles hold 2 ounces each, which is enough for the light misting a station wipe-down needs: dampening a cloth to pick up fine dust from the label board, the fence face, and the surfaces around the push stick hooks. Two bottles in the pack means one can hold plain water and the second a diluted cleaning solution, labeled accordingly.
The small capacity is the point and also the limit. Two ounces will not wash down a whole bench, and these are not the bottles for flooding a surface or applying finish. They are sized for the station, filled in seconds at the sink, and light enough to hang or stand in the small footprint next to the push sticks without crowding them. For a reset routine built around small, frequent wipe-downs rather than rare deep cleans, that size is the right match.
Specs
- Product type: small spray bottles
- Capacity: 2 ounces per bottle
- Count: 2 bottles per pack
- Spray pattern and nozzle type: not stated, confirm on the listing
- Bottle material: not stated
How to choose
Work through the station in the order the reset actually happens. Start with hardware: if the station’s jigs and fixtures use hex socket bolts, the toolant bit set is the first pick, and the size spread in a 20 piece set covers most of what a saw station accumulates. Move to labeling next. Any station that posts setup cards, fence positions, or blade logs on a board will use the Arrow T25 staples, provided the shop’s staple gun takes the T25 style, which is worth confirming before ordering.
Then look at the bench surface itself. A station with a chronic scatter of small loose hardware benefits from the Anvin kit as a containment point, with the understanding that its contents are guitar accessories and only the case earns its keep. A station in a dusty shop benefits from the LiBa brush for dry dusting of surfaces during the reset, kept strictly to cleaning duty on an idle saw. Finally, the RELANOR bottles suit any station where the wipe-down step keeps getting skipped for lack of a bottle at hand. Shops that already own these basics should buy only the missing layer rather than the whole list.
Who should skip
Skip this list if the station’s actual problem is the push sticks themselves. Worn, chewed-up, or missing push sticks need replacing with real push sticks, and nothing here does that job. Skip it as well if the shop already runs a disciplined reset routine with stocked consumables, because these are restock supplies, not upgrades. Guitar players will get full value from the Anvin kit; non-players should weigh whether a small case alone justifies it, and anyone wanting divided small-parts storage should choose a purpose-built organizer instead. Finally, anyone expecting the brush or the bottles to play any role during a cut should skip them entirely, because they are cleaning items for an idle station, full stop.
FAQ
Is any product on this list a push stick or a push stick replacement?
No. None of the five picks is a push stick, a push block, or a featherboard, and none of them should be used to feed stock or hold material near a blade. They are reset supplies for the station around the push sticks: labeling, hardware tightening, small-parts containment, dusting, and wipe-down.
Why is a guitar accessories kit in a woodworking article?
For its case, not its contents. A station reset turns up loose small hardware, and a compact kit package corrals it. The accessories inside are guitar accessories, stated plainly, so a reader who wants a divided parts organizer should buy one of those instead.
Can the LiBa brush be used to clear sawdust off the saw while cutting?
No. The brush is for dry dusting surfaces during a reset while the saw is idle and powered down. It is a soft personal care brush with no shop safety rating, and it must never be used near a spinning blade or to move stock or offcuts.
What should I check before ordering the staples and bits?
Confirm that the shop staple gun accepts T25 staples, since staple styles are not interchangeable. For the bit set, confirm the hex sizes and shank style on the listing against the hardware actually used at the station, because the exact size list is not stated in the product name.
Final verdict
A push stick station reset is unglamorous work, and that is exactly why it needs a supplies list of its own. The Arrow staples refresh the labels, the toolant bits tighten the hardware, the Anvin kit corrals the small loose parts, the LiBa brush handles gentle dry dusting on an idle saw, and the RELANOR bottles make the wipe-down easy enough to actually happen. None of them replaces a push stick or any other safety equipment, and the article has not pretended otherwise. Bought as a restock kit for a station that has drifted, they cover the full reset pass in one order.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!