Key takeaways
- Compare five wood turning tool rests for steady, catch-free cuts, from a 6-inch stainless rest to a four-piece set for mini, midi, and full-size lathes.
A lathe tool rest does quiet work. It holds your gouge at the right height, gives the tool a steady fulcrum, and keeps the cutting edge close to the wood so a catch stays a small scare instead of a ruined blank. The rest that ships with a lathe is often the weakest part of the machine, short, soft, or nicked along the top edge, so an aftermarket rest is one of the cheapest real upgrades a turner can buy.
As an Amazon Associate, I earn from qualifying purchases.
How to Choose a Wood Turning Tool Rest
Start with post diameter, because a rest that does not fit your banjo is useless. Most mini and midi lathes take a 5/8 inch post, while larger lathes take a 1 inch post. Measure your banjo or check your lathe manual before ordering, and note that some imported lathes use a 25 mm post, which is close to but not the same as 1 inch.
Next, match the rest length to the work. Short rests are stiffer and give the best control for pens, small bowls, and detail work. Long rests reach across spindles and platters without constant repositioning, but a long rest flexes more, so keep the tool close to the post and the rest close to the wood.
Look at the top edge. A hardened steel rod or a smooth stainless bar lets the tool glide without catching on nicks. Cast iron rests are heavy and steady but need the top kept smooth and free of rust. A flat platform rest is a different animal entirely: it supports square-shaft tools and scrapers flat, which helps when hollowing deep vessels.
Finally, think about shape. Straight rests handle most spindle work. Curved and S-curved rests reach around bowl interiors so the tool stays close to the wall.
The 5 Best Wood Turning Tool Rests
Simple Woodturning Tools Tool Rest Platform
This flat platform rest was designed for hollowing, and it shows. The rectangular stainless plate supports square-shaft tools flat, so the cutter stays at center height and the tool cannot teeter on a round bar the way it can on a standard rest. A clamping collar on the post holds the height setting while you swing the banjo around the lathe.
- Specs:
- Rest width: 7 in
- Post diameter: 5/8 in
- Flat rest: 1/2 in thick by 1-1/2 in wide stainless steel
- Post length: 4 in
- Included: flat rest, post, cap screw, clamping collar, hex key
- Made in: USA
One crawl of the listing showed no featured offers available, so check stock before ordering. If your turning is mostly spindle work, a straight bar rest below will serve you better than this flat platform.
Robust Mini Rest
Robust has built its name on tool rests, and the Mini Rest is the one most small-lathe owners reach for. The hardened steel rod on top is the key detail: it stays smooth and nick-free far longer than a cast bar, so tools glide instead of grabbing.
The 5/8 inch post fits most mini and midi lathes, including Jet, Delta, Rikon, and Grizzly small lathes. Robust offers its mini rests in several widths, so confirm which width the listing you open shows before ordering.
- Specs:
- Post diameter: 5/8 in
- Top: hardened steel rod
- Fits: most mini and midi lathes with 5/8 in banjos
- Made in: USA
This is the premium pick of the group. If the budget is tight, the stainless rests below give up some refinement but keep the same post size and a smooth top.
SIIIXS 12 Inch Stainless Steel Lathe Tool Rest
For long spindles, chair legs, and table legs, a 12 inch rest means fewer stops to slide the banjo. This SIIIXS bar is stainless steel throughout, so humidity and hand sweat do not seize the post in the banjo the way carbon steel can, and the T-type design keeps the rest simple and rigid.
The 5/8 inch post fits the standard mini and midi banjo, and at just over a pound it is light enough to swap in and out without a struggle.
- Specs:
- Rest length: 12 in
- Post diameter: 5/8 in
- Material: stainless steel
- Weight: 1.1 lb
- Model: SDJ16
A long rest flexes more than a short one, so keep the cutting point near the post on heavy roughing cuts and slide the banjo along as the work progresses.
Vkinman 6 Inch Lathe Tool Rest
The short rest in this roundup is the one to buy when the lathe is small or the work is small. Six inches of rest is plenty for pens, bottle stoppers, small bowls, and detail work, and the short bar is the stiffest shape here, which means less vibration and fewer catches when the tool is close to the post.
It is stainless steel with a 5/8 inch post and a locking nut, so it drops into the same mini and midi banjos as the rests above. For a first lathe or a second rest dedicated to small work, this is the practical, low-cost choice.
- Specs:
- Rest length: 6 in
- Post diameter: 5/8 in
- Material: stainless steel
- Design: T-type with locking nut
Do not expect a 6 inch rest to span a chair leg. Pair it with a longer rest, such as the SIIIXS above, if you turn spindles of any real length.
BMWOOD 1 Inch Post 4-Piece Tool Rest Set
If your lathe takes a 1 inch post, this set is the most versatile buy here. Four straight rests in 3-1/2, 6, 9, and 12 inch lengths share one post size, so you pick the length that matches the blank instead of stretching one rest across every job.
Each rest has a hardened steel rod on top for a smooth glide, and the 1 inch post fits the larger banjos found on most full-size and 14 inch lathes.
- Specs:
- Set contents: 4 rests, 3-1/2, 6, 9, and 12 in
- Post diameter: 1 in
- Top: hardened steel rod
- Design: straight rests with round bar top
Measure your banjo before ordering. A 1 inch post will not fit a 5/8 inch banjo, and this set is built for the bigger lathes.
Comparison
| Rest | Length | Post | Best For |
|---|---|---|---|
| Simple Woodturning Tools Platform | 7 in | 5/8 in | Hollowing bowls and vessels |
| Robust Mini Rest | Mini | 5/8 in | Everyday turning on small lathes |
| SIIIXS Stainless Rest | 12 in | 5/8 in | Long spindles and legs |
| Vkinman Stainless Rest | 6 in | 5/8 in | Pens and small detail work |
| BMWOOD 4-Piece Set | 3-1/2 to 12 in | 1 in | Full-size lathes, all lengths |
Four of the five picks use a 5/8 inch post, which matches most mini and midi lathes. Only the BMWOOD set uses a 1 inch post, so it is the pick for larger machines. The Simple Woodturning Tools platform is the only flat rest here; the other four are bar rests, which suit spindle work and general turning better.
FAQ
What post diameter does my lathe need?
Measure the banjo hole or check the lathe manual. Most mini and midi lathes use a 5/8 inch post, and most larger lathes use a 1 inch post. Some imported lathes use a 25 mm post, which will not accept a 1 inch rest, so measure rather than guess.
How close should the tool rest sit to the wood?
As close as practical without touching. A gap of about 1/8 inch is a good target. The farther the tool overhangs the rest, the more leverage the wood has to grab the tool, so slide the rest in close and reposition it often as the blank gets smaller.
At what height should I set the tool rest?
Set the top of the rest so the cutting edge works at or slightly above the centerline of the spinning blank. A rest set too low lets the rotation pull the tool away from the wood, which is when catches happen. Lock the banjo firmly before starting the lathe.
Do I need a curved rest for bowls?
Not to start. A straight rest handles the outside of a bowl and shallow interiors. A curved or S-curved rest earns its keep when you hollow deep bowls, because it lets the tool reach the inside wall while the rest stays close to the work.
How do I keep a tool rest top smooth?
Wipe the top clean after each session and file out any nicks with a fine metal file, then smooth the spot. Stainless and hardened steel tops need this far less often than cast iron.
Conclusion
A good tool rest is a small purchase that changes how a lathe feels. Match the post to your banjo first, then pick the length and shape for the work you actually do. The Simple Woodturning Tools platform is the pick for hollowing, the Robust Mini Rest is the premium everyday rest for small lathes, the SIIIXS 12 inch bar covers long spindles, the Vkinman 6 inch rest is the cheap and stiff choice for small work, and the BMWOOD four-piece set is the versatile answer for a full-size lathe with a 1 inch banjo.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!