Updated Nov 22, 2026· 5 min read

Our Top Picks

  1. POWERTEC 71164 Cam Clamp 2-Pack
    Check on Amazon
  2. POWERTEC 71168-P2V T-Track Hold Down Clamp 4-Pack
    Check on Amazon
  3. MICROJIG MatchFit Grr-rip Clamp DVC-625QCK2 2-Pack
    Check on Amazon

A router table fence that drifts even a hair ruins a cut. A good fence clamp locks the fence to the table or to the T-track, holds it square through the pass, and releases in seconds when you need to move it. The wrong clamp slips, mars the fence, or only fits one track size.

Our top pick: Milescraft 7209 Universal Fence Clamp 4-Pack. Runner-up: POWERTEC 71164 Cam Clamp 2-Pack.

As an Amazon Associate, I earn from qualifying purchases.

How to Choose a Router Table Fence Clamp

Start with the track. Most router tables use a universal T-track with a 3/4 inch by 3/8 inch slot, but some use a smaller 1/4 inch track or a dovetail groove. Measure the slot before you buy, because a clamp with the wrong bolt will not seat.

Next, decide how the clamp holds. A universal fence clamp hooks over the fence and the table edge and squeezes them together. A T-track hold-down drops a bolt into the track and presses a pad down on the fence base. A cam lever trades a knob for a flip lever, which is faster for repeated setups. A dovetail clamp grips a dovetail groove and works from either side.

Check the clamping range. Thin fences and thick fences need different jaw openings, and a clamp that cannot close on your fence is useless. Look for non-marring pads if your fence face is aluminum or finished wood. Finally, think about how many you need. One clamp per side is the minimum for a fence; two per side holds better on long fences.

The 5 Best Router Table Fence Clamps

Milescraft 7209 Universal Fence Clamp 4-Pack

The Milescraft 7209 is a classic fence clamp that hooks over the fence and pulls it tight against the table edge. It works on mitre saws, router tables, table saws, and clamping squares, so it earns its keep beyond the router table.

  • Specs: 4-pack; 3/8 inch threaded rod; rigid aluminum body; fits fences on router tables, mitre saws and table saws

POWERTEC 71164 Cam Clamp 2-Pack

The POWERTEC 71164 swaps the usual knob for a cam lever. Flip the lever and the clamp locks; flip it back and the fence slides free. That speed matters when you move the fence between passes.

  • Specs: 2-pack; 1/4-20 thread; 3 inch T-track bolts included; die cast aluminum body with blue anodized coating; steel and rubber washers included

POWERTEC 71168-P2V T-Track Hold Down Clamp 4-Pack

The POWERTEC 71168-P2V is a lever-shaped hold-down that drops into a universal T-track and presses down on the fence base. The five-star knob gives plenty of leverage, and the rubber pad protects the fence from marks.

  • Specs: 4-pack; 5-1/2 inch long by 1-1/8 inch wide; anodized aluminum body; non-marring rubber pads; 3-1/2 inch T-bolt with 5/16-18 thread

MICROJIG MatchFit Grr-rip Clamp DVC-625QCK2 2-Pack

The MICROJIG Grr-rip clamp is the odd one out, and that is its strength. It grips a dovetail groove instead of a T-track, so it works on fences and jigs cut with a dovetail router bit. A squeeze handle applies the pressure, and an anti-pivot spring keeps the arm from sliding when you let go.

  • Specs: 2-pack; dovetail groove compatible; squeeze-action handle; dual clamp pressure caul; anti-pivot spring; model DVC-625QCK2

POWERTEC 71438 T-Track Clamp Vice 2-Pack

The POWERTEC 71438 is a small clamp vice for T-tracks that accept 1/4 inch hex head bolts. It clamps from above and holds the fence base or a stop block firmly in the track, and its compact size fits crowded fences.

  • Specs: 2-pack; fits T-tracks accepting 1/4 inch hex head bolts; model 71438

Comparison

Clamp Type Pack Best For
Milescraft 7209 Universal fence clamp 4 Hooking over almost any fence
POWERTEC 71164 Cam lever clamp 2 Fast repeated fence moves
POWERTEC 71168-P2V T-track hold-down 4 Pressing a fence base into a T-track
MICROJIG DVC-625QCK2 Dovetail clamp 2 Dovetail-groove fences and jigs
POWERTEC 71438 T-track clamp vice 2 Compact hold-downs in tight spaces

If your fence has no track at all, start with the Milescraft 7209. If you move the fence constantly, the POWERTEC 71164 cam levers save the most time. For a tracked table, the POWERTEC 71168-P2V hold-downs are the workhorse pick. The MICROJIG clamps are the right call only if your fence or jig has a dovetail groove, and the POWERTEC 71438 vice fills the gap when space is tight.

FAQ

How many fence clamps do I need?

Two is the minimum, one per side. Four holds a long fence better and stops it from pivoting under load.

Will these clamps fit my router table?

Check your track first. The POWERTEC hold-downs fit universal T-tracks and will not fit 1/4 inch or mini T-tracks. The Milescraft clamps hook over the fence edge and do not need a track at all.

Can I use fence clamps on a table saw or drill press?

Yes. The Milescraft and POWERTEC clamps in this guide are made for table saws, mitre saws, drill press tables, and router tables.

Do cam levers hold as well as knobs?

A cam lever locks with a fixed throw, so it is fast and consistent. A knob lets you fine-tune the pressure. For fences that move often, the cam lever wins; for maximum holding force on a heavy fence, a knob clamp is the safer pick.

What is a dovetail clamp for?

It grips a dovetail-shaped groove routed into a fence or jig. It is not a T-track clamp, so it only works where that groove exists.

Conclusion

A fence that stays put is the difference between a clean profile and a ruined board. The Milescraft 7209 covers nearly any fence, the POWERTEC 71164 cam levers make repeated setups fast, the POWERTEC 71168-P2V hold-downs anchor tracked fences, the MICROJIG Grr-rip clamps serve dovetail grooves, and the POWERTEC 71438 vice handles tight spots. Measure your track, match the clamp to it, and use one clamp per side at minimum.

T
Table Saw Blog Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Woodworking Router Table Fence Clamps: 5 PicksCheck price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.