Updated Nov 20, 2026· 9 min read

Key takeaways

  • Compare the best band saw blades by length, width, TPI and material, from carbon-steel wood blades to M42 bi-metal picks for common shop saws.
⭐ Key Takeaways
Quick answer: Our top pick is POWERTEC 93-1/2 Inch Bandsaw Blade, 3/8 Inch x 6 TPI (13116), with POWERTEC 93-1/2 Inch Bandsaw Blades Assortment, 3-Pack (13603) as a strong alternative.

A band saw is only as good as the blade looped around its wheels. The wrong length will not tension at all, the wrong width will not track through curves, and the wrong tooth count will either tear through thin stock or crawl through thick resaw cuts. Because blades are consumables that dull and snap, most woodworkers keep several on hand and swap them as the work changes.

This guide compares five blades covering the main jobs a shop band saw handles: general woodworking on a 14-inch saw, a starter assortment pack, a low-tension silicon steel blade, a flex-back blade for an 82-inch saw, and an M42 bi-metal blade for cutting metal on a 4×6 saw. Each pick lists its exact length, width and tooth configuration, because the variant is the product.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most 14-inch band saws, the POWERTEC 13116 (93-1/2 inch, 3/8 inch, 6 TPI, carbon steel) is the safest single-blade buy, and the POWERTEC 13603 assortment adds 1/2 inch and 1/8 inch companions in one pack. Timber Wolf’s 92-1/2 inch blade suits low-tension setups, Olson covers 82-inch saws, and Imachinist’s M42 bi-metal blade is the metal-cutting pick.

POWERTEC 93-1/2 Inch Bandsaw Blade, 3/8 Inch x 6 TPI (13116)

POWERTEC 93-1/2 Inch Bandsaw Blade, 3/8 Inch x 6 TPI (13116)

POWERTEC 93-1/2 Inch Bandsaw Blade, 3/8 Inch x 6 TPI (13116)

Check price on Amazon

POWERTEC’s 13116 is a single high carbon steel blade sized for the most common band saw in home shops: the 14-inch floor model that takes a 93-1/2 inch loop. The 3/8 inch width is a deliberate middle ground, wide enough to track straight on rip cuts and light resawing, yet narrow enough to turn moderate curves that a 1/2 inch blade would refuse. The 6 TPI tooth count splits the difference the same way, clearing chips from softwood and plywood without the ragged finish of a 3 or 4 TPI hook tooth blade.

POWERTEC states the teeth are hardened to RC 64-66 and that every weld is finished for proper tooth spacing and matched set, which matters because a poor weld thumps through the guides once per revolution. As a budget tier blade, it is the one to keep mounted for everyday work and replace without hesitation once cuts drift.

Specs:

  • Blade length: 93-1/2 inches
  • Blade width: 3/8 inch
  • Teeth per inch: 6 TPI
  • Blade thickness: 0.025 inch
  • Material: high carbon steel
  • Model: 13116 (listed model number 13116X)
  • Tooth hardness: RC 64-66, per the maker
  • Fits: most 14-inch band saws from Delta, Grizzly, JET, Rikon, Shop Fox, Rockwell and others

POWERTEC 93-1/2 Inch Bandsaw Blades Assortment, 3-Pack (13603)

POWERTEC 93-1/2 Inch Bandsaw Blades Assortment, 3-Pack (13603)

POWERTEC 93-1/2 Inch Bandsaw Blades Assortment, 3-Pack (13603)

Check price on Amazon

The 13603 assortment answers a different question: what should a new band saw owner buy first? Instead of one compromise blade, the pack bundles three 93-1/2 inch high carbon steel blades that divide the work between them. The 1/2 inch, 6 TPI blade handles ripping and shallow resawing, the 1/4 inch, 6 TPI blade covers general cutting and gentler curves, and the 1/8 inch, 14 TPI blade is the scroll specialist of the set.

All three blades share the same length, so they swap onto any 14-inch saw that takes a 93-1/2 inch loop, including the Delta, Grizzly, Rikon, Craftsman, JET, Shop Fox and Rockwell models POWERTEC lists, and the teeth carry the same RC 64-66 hardening as the single blades. For a shop that has just unboxed a saw, this budget tier pack is a practical way to learn what each width does before buying premium blades.

Specs:

  • Blade length: 93-1/2 inches (all three blades)
  • Contents: 1/2 inch x 6 TPI, 1/4 inch x 6 TPI and 1/8 inch x 14 TPI blades
  • Blade thickness: 0.025 inch
  • Material: high carbon steel
  • Model: 13603
  • Pack count: 3 blades
  • Fits: 14-inch band saws from Delta, Grizzly, Rikon, Sears Craftsman, JET, Shop Fox and Rockwell

Timber Wolf Bandsaw Blade, 92-1/2 Inch x 1/2 Inch x 10 TPI

Timber Wolf Bandsaw Blade, 92-1/2 Inch x 1/2 Inch x 10 TPI

Timber Wolf Bandsaw Blade, 92-1/2 Inch x 1/2 Inch x 10 TPI

Check price on Amazon

Timber Wolf blades, sold by PS Wood Machines, take a different approach to blade steel. The company uses a high silicon, low carbide steel and mills the teeth rather than stamping them, a combination it rates for running at lower tension than conventional carbon blades. Lower tension is easier on wheel bearings, tyres and the frame, which is why these blades have a following among owners of lighter 14-inch saws.

This variant is a 92-1/2 inch loop, 1/2 inch wide with a fine 10 TPI pitch and a 0.025 inch thickness. That makes it a finish-leaning blade: the width keeps it tracking straight, while the finer tooth count suits thinner stock, veneer work and cleaner crosscuts rather than deep resawing. Note the length before ordering. At 92-1/2 inches it is an inch shorter than the standard 93-1/2 inch blade, so it fits only the saws PS Wood lists for this size. It sits in the premium tier here.

Specs:

  • Blade length: 92-1/2 inches
  • Blade width: 1/2 inch
  • Teeth per inch: 10 TPI
  • Blade thickness: 0.025 inch
  • Material: high silicon, low carbide steel
  • Brand: Timber Wolf (PS Wood Machines)
  • UPC: 669754925108

Olson Saw FB19282DB Band Saw Blade, 82 Inch x 3/8 Inch x 4 TPI Skip

Olson Saw FB19282DB Band Saw Blade, 82 Inch x 3/8 Inch x 4 TPI Skip

Olson Saw FB19282DB Band Saw Blade, 82 Inch x 3/8 Inch x 4 TPI Skip

Check price on Amazon

Not every shop saw takes a 93-1/2 inch blade, and owners of 82-inch machines have a shorter catalogue to shop from. Olson Saw, manufacturing in the USA since 1918, fills that gap with the FB19282DB, an 82 inch hard edge flex back blade. The flex back design pairs a hard tooth edge with a softer, flexible backing, so the blade tolerates the tighter wheels of smaller saws without fatiguing as quickly.

The 3/8 inch width and coarse 4 TPI skip tooth pattern mark this out as a fast-cutting general purpose blade. Skip teeth have wide gullets that clear chips quickly in thick or resinous softwood, at the cost of a rougher surface. It is a sensible budget tier default for an 82-inch saw used on construction lumber and rough blanks, where speed matters more than a finish-ready surface.

Specs:

  • Blade length: 82 inches
  • Blade width: 3/8 inch
  • Teeth per inch: 4 TPI, skip tooth
  • Blade thickness: 0.025 inch
  • Material: hard edge flex back carbon steel
  • Model: FB19282DB
  • UPC: 012373192824
  • Manufacturer: Blackstone Industries (Olson Saw)

Imachinist S64121224SS M42 Bi-Metal Bandsaw Blade, 64-1/2 Inch x 1/2 Inch x 24 TPI

Imachinist S64121224SS M42 Bi-Metal Bandsaw Blade, 64-1/2 Inch x 1/2 Inch x 24 TPI

Imachinist S64121224SS M42 Bi-Metal Bandsaw Blade, 64-1/2 Inch x 1/2 Inch x 24 TPI

Check price on Amazon

The first four picks are wood blades. The Imachinist S64121224SS is the metal-cutting entry, built for the horizontal 4×6 band saws that take a 64-1/2 inch loop. Its edge is M42 high-speed steel bonded to a flexible backing, the standard bi-metal construction for blades that have to survive steel, and the listing names stainless steel and hard metal as its work.

The 24 TPI constant tooth pitch is very fine, which is exactly what thin-walled tube, sheet and small bar stock need: enough teeth engaged in the cut to avoid snagging and tooth strippage. The trade-off is speed in thick material, where a coarser variable pitch blade clears chips faster. Imachinist is a specialist maker that produces band saw and hack saw blades for metal only, and this mid-range pick gives the list a genuine option for shops that cut metal too.

Specs:

  • Blade length: 64-1/2 inches
  • Blade width: 1/2 inch
  • Teeth per inch: 24 TPI, constant pitch
  • Blade thickness: 0.025 inch
  • Material: M42 bi-metal
  • Model: S64121224SS
  • Fits: 4×6 band saws using 64-1/2 inch blades
  • Intended materials: stainless steel and hard metal, per the maker

How to choose

Start with length, because it is not negotiable. The blade must match your saw’s specified loop length exactly; a blade even slightly off will not tension or track. Check the manual or the plate inside the wheel cover, and remember that fitting a riser block changes the required length.

Width decides how tight a curve you can cut. Narrow blades, 1/8 and 1/4 inch, turn small radii for scroll work. A 3/8 inch blade is the all-rounder, and 1/2 inch and wider blades track straightest for ripping and resawing, provided your saw can tension them. Tooth count trades speed against finish: 3 to 6 TPI clears chips in thick wood, 10 to 14 TPI leaves a cleaner cut in thin stock, and fine pitches of 18 TPI and above are for thin metal.

Material sets the ceiling. High carbon steel blades like the POWERTEC and Olson picks are inexpensive, flexible and adequate for wood. Silicon steel, as in the Timber Wolf, allows lower running tension. Bi-metal blades such as the Imachinist cost more but hold an edge far longer in metal and abrasive material. Match the material to what you cut most, and keep a spare of your main size.

Who should skip

Skip this roundup if your saw takes a length none of these picks cover, such as the 59-1/2, 70-1/2, 80 or 105 inch loops used by many benchtop and riser-equipped saws. Skip the wood blades if you mostly cut steel, and skip the Imachinist if you only cut wood, since a 24 TPI metal blade will crawl and scorch in timber. Dedicated resaw work in tall hardwood deserves a wider resaw blade rather than the general purpose widths here. Finally, if your saw’s guides or tension spring are worn, fix those first; no new blade tracks well on a saw that cannot hold it straight.

FAQ

How do I find the blade length my band saw needs?

Check the owner’s manual or the specification plate inside the upper wheel cover. If neither is available, mark the old blade, roll it along the floor for one full revolution, and measure the distance travelled. Common lengths include 64-1/2, 82, 92-1/2 and 93-1/2 inches.

What TPI should I choose for general woodworking?

A 6 TPI blade in a 1/4 or 3/8 inch width is the usual general purpose compromise. Go coarser, 3 to 4 TPI, for thick stock and resawing, and finer, 10 to 14 TPI, for thin stock and smoother cuts.

Can I cut metal with a wood band saw blade?

Carbon steel wood blades can handle thin non-ferrous metal such as aluminium sheet in a pinch, but they dull quickly in steel. For regular metal cutting, use a bi-metal blade with a fine pitch, such as the 24 TPI Imachinist here, on a saw that runs at metal-cutting speeds.

How long should a band saw blade last?

It depends on the material cut, blade tension and feed pressure. Carbon steel wood blades are consumables, often replaced after a few big projects, while bi-metal blades typically outlast several carbon blades. A blade that starts drifting, burning or needing heavy feed pressure is telling you it is done.

Final verdict

For the typical 14-inch band saw, buy the POWERTEC 13116 if you want one dependable blade, or the POWERTEC 13603 assortment to cover curves, ripping and scroll work in a single purchase. Timber Wolf’s 92-1/2 inch blade is the premium choice where its shorter length fits. Olson keeps 82-inch saws supplied with a fast, flexible general purpose blade, and the Imachinist M42 bi-metal is the pick when the material is steel rather than timber. Whichever you choose, confirm the loop length against your saw first; that single measurement decides whether a blade is right at all.

T
Table Saw Blog Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Band Saw Blades: Top Picks for Wood…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.