Key takeaways
- Compare the best trim routers for edging, laminate and hinge mortises, with corded and cordless palm routers ranked by power, speed range and weight.
A trim router, also called a palm router or laminate trimmer, is the router most woodworkers reach for first. It is light enough to guide with one hand and strong enough for roundovers, chamfers, flush trimming laminate and veneer, and cutting hinge mortises. Where a full-size router feels like overkill, a compact router gives you direct control over the cut.
This guide compares five trim routers, three corded and two cordless, on the specifications that separate them: motor power, speed range, depth adjustment, base design, and weight. Every model here uses a 1/4-inch collet and comes from a major tool brand. One of these five will fit almost any shop, whether you trim laminate weekly or just want a second router that can stay set up with a roundover bit.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
The Makita RT0701C is the best trim router for most shops, with its 1-1/4 HP motor, 10,000 to 30,000 RPM speed range, and rack-and-pinion depth adjustment. The Milwaukee M18 FUEL 2723-20 leads the cordless picks, the Bosch Colt kit adds an edge guide, and the Ryobi PCL424B is the budget cordless pick.
Makita RT0701C 1-1/4 HP Compact Router
The Makita RT0701C is the benchmark corded trim router, and it earns that spot on specifications. Its 6.5-amp motor is rated at 1-1/4 HP maximum, and the variable speed dial runs from 10,000 to 30,000 RPM, the lowest bottom speed in this group. That slow bottom end matters when you run larger-diameter edge bits or work in plastic, where a fast bit melts instead of cutting.
Depth adjustment is rack-and-pinion, so turning the dial moves the motor in the base in small, repeatable steps instead of relying on a clamp and a guess. The aluminum motor housing keeps the tool at 3.9 pounds, light enough for one-handed edge work but heavy enough to stay planted. Makita also sells plunge, tilt, and offset bases for this motor, so the RT0701C can grow into a small routing system over time. Electronic speed control holds RPM under load, and soft start keeps the tool from twisting at startup.
This is a mid-range, corded, fixed-base tool with a straight guide and wrenches in the box. If you want one trim router that covers the widest range of bits and materials, this is the safest pick here.
Specs
- Motor: 1-1/4 HP maximum, 6.5 amps
- Speed: variable, 10,000 to 30,000 RPM
- Collet: 1/4 inch
- Base: fixed, rack-and-pinion fine depth adjustment
- Power source: corded, 120 volts
- Weight: 3.9 lb
- Extras: soft start, electronic speed control; plunge, tilt, and offset bases sold separately
DEWALT DWP611 Compact Router
The DEWALT DWP611 matches the Makita on headline power, with a 1-1/4 HP motor drawing 7.7 amps, but takes a different approach to control. Its variable speed range runs from 16,000 to 27,000 RPM, narrower than the Makita at both ends, which is fine for the small-diameter bits trim routers usually spin. The standout feature is the pair of LED work lights in the base, which light the bit area directly and make it easier to follow a scribe mark in a dim shop corner.
Depth changes use an adjustment ring with a clamp release, and the base removes quickly for bit changes. At 4.6 pounds with the fixed base fitted, the DWP611 is the heaviest corded tool in this group, which some will feel as stability and others as bulk during long edging sessions. The motor also accepts DEWALT’s plunge base, sold on its own or in the DWP611PK combo kit, for hinge mortises and stopped grooves.
Choose the DWP611 if cut-line visibility is your priority and you may add a plunge base later. It sits in the mid-range tier.
Specs
- Motor: 1-1/4 HP, 7.7 amps
- Speed: variable, 16,000 to 27,000 RPM
- Collet: 1/4 inch
- Base: fixed; plunge base sold separately or in the DWP611PK kit
- Power source: corded
- Weight: 4.6 lb with fixed base
- Extras: dual LED work lights, soft start, adjustment ring depth control
Bosch PR20EVSK Colt Palm Router Kit
The Bosch Colt is the original palm router, and the PR20EVSK kit pairs the PR20EVS motor with a straight edge guide in one box. The motor is the smallest here on paper, rated at 1 HP and 5.6 amps, but it spins the fastest: the variable speed range tops out at 35,000 RPM. That high top speed suits small trim and edging bits, and Bosch’s Constant Response circuitry keeps speed steady as the load changes, while soft start ramps up smoothly.
The Colt’s quick-clamp system lets you slide the motor in and out of the fixed base fast, and fine depth adjustment is handled by a dial on the base. The tool is compact and light, which is why it remains a favorite for laminate work, where the router rides along a countertop edge for long stretches. The trade-off for the smaller motor is real: deep cuts and wide profile bits call for lighter passes than the 1-1/4 HP tools need.
This is a mid-range corded kit. Buyers who mostly trim laminate, veneer, and edge banding get a complete package here.
Specs
- Motor: 1 HP, 5.6 amps
- Speed: variable, 16,000 to 35,000 RPM
- Collet: 1/4 inch
- Base: fixed, quick-clamp motor release
- Power source: corded
- Weight: about 3.3 lb
- Extras: soft start, Constant Response circuitry, straight edge guide included in kit
Milwaukee M18 FUEL Compact Router (2723-20)
The Milwaukee 2723-20 is the premium pick and the strongest cordless trim router in this group. Milwaukee rates its brushless motor as delivering the power of a corded 1.25 HP trim router, and its variable speed dial covers 10,000 to 31,000 RPM, matching the corded tools on range. Because it runs on the M18 battery platform, it suits installers and anyone who trims parts away from a bench outlet.
At 2.95 pounds for the bare tool, it is the lightest router here, and the fixed base uses a fine-adjustment dial with a quick-release clamp. The bare tool package is generous: a straight edge guide, a dust shroud, and both a round sub-base and a larger template sub-base are included. Milwaukee also sells plunge and offset bases, and rates the tool for up to 250 linear feet of 3/8-inch roundover in red oak per charge with a 5.0Ah battery, though runtime varies with bit and material.
The 2723-20 is a bare tool, so it makes the most sense if you already own M18 batteries.
Specs
- Motor: brushless, rated at 1.25 HP corded equivalent
- Speed: variable, 10,000 to 31,000 RPM
- Collet: 1/4 inch
- Base: fixed, 4-inch round sub-base; plunge and offset bases sold separately
- Power source: 18-volt M18 battery, sold separately
- Weight: 2.95 lb, tool only
- Extras: edge guide, dust shroud, and template sub-base included
Ryobi ONE+ PCL424B Compact Router
The Ryobi PCL424B is the budget pick, a cordless trim router built for the ONE+ 18-volt platform. Its variable speed dial runs from 20,000 to 30,000 RPM, a range that starts higher than the other tools here, so it is aimed squarely at the small roundover, chamfer, and trim bits that make up most palm routing, rather than large bits that need slow speeds.
Depth adjustment combines a quick-release lever for coarse changes with a micro-adjustment for fine tuning, a pairing usually found on pricier tools. The router weighs 3.22 pounds and ships as a bare tool with a collet wrench and a vacuum dust chute in the box. Battery and charger are sold separately, which keeps the entry cost low for anyone who already owns ONE+ batteries.
Power is the honest limitation: this is a light-duty router for edging, trimming, and shallow cuts, not a substitute for a corded 1-1/4 HP tool on deep profiles. For hobby shops and first-time router buyers on the ONE+ platform, it covers the common jobs at the lowest tier in this guide.
Specs
- Motor: 18-volt cordless, ONE+ platform
- Speed: variable, 20,000 to 30,000 RPM
- Collet: 1/4 inch
- Base: fixed, micro and macro depth adjustment
- Power source: 18-volt ONE+ battery, sold separately
- Weight: 3.22 lb
- Extras: collet wrench and vacuum dust chute included; battery and charger sold separately
How to choose
Start with power source. Corded trim routers like the Makita, DEWALT, and Bosch deliver constant power for long sessions, while cordless models like the Milwaukee and Ryobi trade a little endurance for total freedom of movement. If you already own one platform’s 18-volt batteries, that alone can decide the question.
Next, look at the speed range. A low minimum speed, around 10,000 RPM, gives control with larger edge-forming bits and heat-sensitive materials; a high top speed suits small trim bits. Then check depth adjustment: rack-and-pinion and micro-adjust systems make repeatable shallow passes easier to dial in. Base options matter too: a fixed base covers edging and trimming, a plunge base adds mortises and stopped cuts, and an offset base reaches into corners. Finally, weigh the tool; the difference between the 2.95-pound Milwaukee and the 4.6-pound DEWALT is obvious after an hour of edging.
Who should skip
Skip trim routers entirely if your work centers on raised-panel doors, wide profile bits, deep mortises, or heavy dado cutting. Those jobs need a full-size router with a 1/2-inch collet and 2 HP or more, ideally mounted in a table. A trim router’s 1/4-inch collet also rules out the large bits many shops already own. If most of your routing happens in a table, buy a mid-size combo kit first; a palm router is a second router for most shops, not the only one.
FAQ
What is a trim router used for?
Trim routers handle light, guided cuts: rounding over and chamfering edges, flush trimming laminate and edge banding, cutting hinge and lock mortises, and routing small grooves and inlays. Their small bases and light weight make them easier to control on edges than full-size routers.
Can a trim router cut dadoes and mortises?
It can cut shallow dadoes and small mortises in several light passes, especially with a plunge base, but it is slow work. Deep or wide joinery cuts are better left to a full-size plunge router, which has the power and the 1/2-inch collet that larger straight bits need.
Is a corded or cordless trim router better?
Neither is better outright. Corded models give unlimited runtime and steady power at a lower tier, which suits bench work. Cordless models are easier to maneuver around large panels and on site, but runtime depends on battery size, and a bare tool assumes you already own batteries and a charger.
What size bits do trim routers take?
All five routers in this guide use a 1/4-inch collet, so they take the wide range of 1/4-inch shank trim, edging, and small profile bits. They cannot use 1/2-inch shank bits, which is why large raised-panel and heavy profile bits belong to full-size routers.
Final verdict
For most woodworkers, the Makita RT0701C is the trim router to buy: the widest speed range, proven depth adjustment, and a family of accessory bases make it the most versatile tool here. The DEWALT DWP611 is the pick when work lights matter, the Bosch Colt kit suits dedicated laminate trimming, the Milwaukee 2723-20 leads the cordless class, and the Ryobi PCL424B opens cordless routing to ONE+ owners at a budget tier.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.

Write Your Review
No reviews yet. Be the first to share your experience!