Updated Nov 19, 2026· 9 min read

Key takeaways

  • Restock the small things your bench runs through: Allen bits, shop vac bags, utility scissors, a stool fix, and a sharpening rod for tidy toolbox days.

Every woodworker’s bench runs on small things that quietly wear out, wander off, or run dry. The Allen bit that rounds over, the shop vac bag that fills up mid-cleanup, the scissors that vanish into a drawer of offcuts — none of them stop a project on their own, but together they slow every job down. A short, deliberate restock day a few times a year keeps the toolbox and the bench area stocked with the consumables and small helpers that get used up fastest.

This guide rounds up five restock staples worth checking on your next toolbox restock day: a fresh Allen bit set, a pack of shop vac bags, a sturdy pair of utility scissors, a clamp fix for the sinking bench stool, and a sharpening rod for the blades that live at the bench. Each one replaces something that wears, fills, dulls, or sags over time. Work through the list, check what is actually running low in your shop, and restock only what you need.

As an Amazon Associate, we earn from qualifying purchases.

1. toolant Impact Allen Wrench Drill Bit Set, 20-Piece Metric & SAE, 2-Inch

Check price on Amazon

Hex fasteners show up everywhere in a wood shop: flat-pack jigs, machine stands, router table inserts, knockdown furniture hardware, and the adjustment points on half the tools on the bench. A dedicated set of Allen bits for a drill or impact driver turns those fasteners from a slow hand-wrench job into a quick one, and a restock day is the right time to replace the bits that have started to round or twist.

This 20-piece set covers both metric and SAE sizes, which matters in a shop where hardware from different makers mixes freely. The 2-inch length suits most driver chucks and gives a little extra reach into recessed fastener heads. Because the set is built for impact use, the bits are meant to go in an impact driver or drill rather than being limited to a hand handle. Keep the set in the top tray of the toolbox so the full range stays together, and retire individual bits as their corners wear — a worn hex bit damages fastener heads, so swapping early is cheaper than extracting a stripped bolt later. Always match the bit size exactly to the fastener, and follow the tool maker’s instructions for driver settings and safe use.

Specs

  • Piece count: 20 pieces
  • Size systems: metric and SAE
  • Bit length: 2 inch
  • Bit profile: Allen (hex)
  • Intended use: impact driver and drill use, per the product name
  • Included sizes, shank style, and case details: confirm on the listing

2. ALYYDBG Shop Vac Bags 5 Pack Type A

Check price on Amazon

Dust collection at the bench lives or dies on small habits, and changing the shop vac bag before it is packed solid is one of them. A full bag chokes suction, works the motor harder, and makes the final cleanup pass — the one that keeps fine dust off finished surfaces — noticeably weaker. Bags are a pure consumable, so they belong on every restock list.

This five pack of Type A bags keeps spares on the shelf so a bag change never has to wait. The Type A designation is the key detail: shop vac bags are not universal, and the letter type has to match the vacuum model they are made for. Check the model named on your current bag or in your vacuum’s manual against the fit information before ordering, and confirm capacity and exact model compatibility on the listing. Swapping in a fresh bag at restock time, rather than waiting until suction drops, also gives you a moment to check the filter and empty any debris sitting in the canister. Dispose of full bags with your regular shop waste according to local guidance, and follow the vacuum maker’s instructions for bag and filter changes.

Specs

  • Pack count: 5 bags
  • Fit designation: Type A
  • Product type: shop vacuum dust bags
  • Compatible vacuum models and bag capacity: confirm on the listing

3. Henckels Come Apart Kitchen Scissors

Check price on Amazon

A good pair of scissors earns a permanent spot at the bench even though this pair comes from a kitchen line. At the bench, scissors open finish and hardware packaging, trim sandpaper sheets down to size, cut tape, twine, veneer edging, and template paper, and snip a dozen other small things a week. The pair that lives at the bench tends to disappear or dull, which makes scissors a classic restock item.

The come-apart design is the practical detail here: the two halves separate, which makes the blades easier to clean after cutting tape or anything sticky, and easier to dry fully before they go back in the drawer. That matters in a shop where adhesive residue builds up fast. Keep this pair assigned to the bench rather than letting it migrate, and reserve it for paper, tape, and light materials rather than wire or metal, which will damage the edges. As with any edged tool, cut away from your body, keep fingers clear of the closing blades, and follow the maker’s instructions for use and care.

Specs

  • Brand line: Henckels
  • Design: come-apart (blades separate for cleaning)
  • Product type: kitchen scissors, used here as bench utility scissors
  • Blade length, handle material, and care instructions: confirm on the listing

4. Salbree Office Chair Clamp Sinking Fix

Check price on Amazon

Almost every shop has the stool: the one that slowly sinks a few inches over the course of a long sanding or assembly session because its lift cylinder no longer holds. Perching lower and lower changes your posture at the bench and makes detailed work harder than it needs to be. A clamp-style fix is a restock-day repair — quick to fit, and far simpler than replacing the whole stool.

This clamp is designed to grip the cylinder shaft of a sinking office chair and hold the seat at a set height, and the same idea applies to a bench stool built on a standard chair cylinder. Fit depends on the cylinder, so measure your stool’s exposed shaft diameter and compare it with the fit range before ordering; the exact diameter range and fitting steps are details to confirm on the listing. Set the stool to your preferred bench height first, then fit the clamp so it holds that height. Check it again after the first few sittings, keep the clamp and shaft clean of sawdust so it grips properly, and follow the maker’s fitting instructions. If your stool wobbles for other reasons — loose casters, a cracked base — a clamp will not solve that, and replacement is the safer call.

Specs

  • Product type: clamp-style sinking chair fix
  • Intended fit: office chair and stool lift cylinders
  • Adjustment: holds seat at a chosen height once fitted
  • Compatible cylinder diameter range and fitting hardware: confirm on the listing

5. 12-Inch Knife Sharpening Rod

Check price on Amazon

The blades that live at the bench — marking knives, shop utility knives, and the kitchen-adjacent knives that wander into the shop for opening boxes and trimming — work better and more predictably when their edges are maintained little and often. A sharpening rod is the restock-day tool for that habit: a few light passes bring a working edge back without setting up a full stone session.

At 12 inches, this rod gives enough working length for comfortable strokes on small and medium blades. Use it for the bench knives you reach for daily, holding a consistent angle and working with light pressure rather than forcing the edge. A rod maintains edges between heavier sharpening sessions; a blade that is chipped or completely dull still needs proper regrinding or stone work first. The rod’s material and surface type are not stated in the product name, so confirm those details on the listing before ordering, especially if you prefer a particular rod type. Store it in a drawer or sheath so the surface stays clean and undamaged, keep your free hand behind the edge’s path, and follow the maker’s instructions for technique and safety.

Specs

  • Rod length: 12 inch
  • Product type: knife sharpening rod
  • Intended use: maintaining edges on knives and small bench blades
  • Rod material, surface type, and handle details: confirm on the listing

How to Choose Toolbox Restock Day Picks

A restock day works best as a short audit rather than a shopping spree. Open the toolbox, the bench drawers, and the shelf where consumables live, and note what is actually worn, missing, or down to the last one. Restock against that list.

For driver bits, check the corners of the sizes you use most; rounding is the signal to replace, and having both metric and SAE covered avoids the mid-project hunt for the one size that fits. For vacuum bags, match the letter type to your exact vacuum model first — fit is everything with bags, and a bargain pack in the wrong type is no bargain. For bench scissors, a come-apart design pays off if you cut tape and packaging often, because the blades clean up quickly and go back to work. For a sinking stool, measure the cylinder shaft before choosing a clamp fix, and be honest about whether the stool has other faults a clamp cannot address. For a sharpening rod, match the length to the blades you maintain most, and confirm the rod material on the listing if you have a preference.

Finally, give everything a home. Bits back in their case, spare bags on the shelf by the vacuum, scissors in the same drawer every time, the rod stored protected. The point of a restock day is not just new stock — it is a bench where the small things are findable, working, and ready, so the next project starts on time. Follow each maker’s instructions for fitting, use, and care, and keep safety guidance from the tool manufacturers in mind whenever you work with drivers, blades, and dust collection.

FAQ

How often should I do a toolbox restock day?

Two to four times a year suits most home shops. Tie it to something you already do — a seasonal cleanup, the start of a big project, or a filter and bag change on the shop vac — and do a quick audit of bits, bags, blades, and other consumables while everything is open.

Will the Type A shop vac bags fit my vacuum?

Only if your vacuum takes Type A bags. The letter type is model-specific, so check the bag currently in your vacuum or the model list in your vacuum’s manual, and confirm the exact compatible models on the listing before ordering. Do not assume bags interchange between brands or models.

Can a clamp fix repair any sinking stool?

It works on stools and chairs with a standard exposed lift cylinder, and only for the sinking problem itself. Measure the shaft diameter and confirm the fit range on the listing. Wobble from loose casters, a damaged base, or a bent column needs repair or replacement instead.

Does a sharpening rod replace sharpening stones?

No. A rod maintains a working edge between fuller sharpening sessions and is ideal for the small knives kept at the bench. A blade that is chipped, rolled badly, or completely dull still needs stone work or regrinding before a rod will help.

T
Table Saw Blog Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Toolbox Restock Day Picks for the Woodwork…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.