Key takeaways
- Compare the best hand planes for woodworking, from a budget No. 4 bench plane to a premium low-angle jack, with specs on soles, irons, and adjustment.
A good hand plane does work that sanders and power planers handle badly: it flattens a board face without rounding the edges, cleans up tear-out on figured grain, and shaves end grain flush with a joint. The confusing part is the numbering system and the long list of near-identical cast-iron bodies.
This guide compares five hand planes that cover the jobs most woodworkers do, from a budget No. 4 smoothing plane that suits a first bench to a premium low-angle jack plane built for shooting board ends. Every pick is listed with its published specifications, so you can match sole length, cutter width, and bed angle to the work you plan to do.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
For a first hand plane, buy the Stanley No. 4 (12-404): its 2-inch cutter, ground cast-iron sole, and quick-release lever cap cover most smoothing work at a budget-tier cost. Add the Stanley No. 9-1/2 block plane for end grain and trimming, and step up to the Stanley No. 62 low-angle jack if you shoot board ends often.
Amazon Basics No. 4 Smoothing Bench Plane — Best Budget Pick
The Amazon Basics No. 4 is the lowest-cost way into bench planing, and its specifications follow the classic pattern: a cast iron body, a 2-inch steel alloy blade, and depth adjustment through a rear adjuster wheel. The version listed here carries wooden handles, and the manufacturer’s manual gives a body length of 9.7 inches and a weight of about 2.7 pounds, in line with traditional No. 4 dimensions.
A No. 4 is a smoothing plane, so this tool is sized for final surface work on boards that are already close to flat: removing mill marks, cleaning up glue lines, and taking fine shavings from tabletops, doors, and drawer parts. Like most budget-tier planes, the iron benefits from a careful honing before serious work, and the sole deserves a quick check for machining residue. Budget a few minutes of setup and the specifications support steady, controlled cuts on common hardwoods and softwoods.
Specs:
- Type: No. 4 smoothing bench plane
- Body material: Cast iron
- Blade: 2-inch steel alloy, adjustable depth
- Body length: 9.7 inches
- Weight: Approximately 2.7 pounds
- Handles: Wooden tote and knob
- Model number: DS-WPAMZ002
Stanley No. 4 Adjustable Bench Plane (12-404) — Best Value Bench Plane
The Stanley 12-404 is the modern version of the most common bench plane ever made. Its gray cast-iron base has precision-ground sides and a machined bottom protected by an epoxy coating, and the 2-inch cutter is hardened, tempered steel. A quick-release cam-lock lever cap makes it fast to pull the iron for honing, and the cutter adjusts for depth and alignment. Polymer handles and knobs are contoured for control.
At 9-3/4 inches long and roughly 2.75 pounds, the 12-404 sits squarely in No. 4 territory: short enough to follow a board’s surface for final smoothing, long enough to level high spots on panels. It accepts the standard Stanley 12-313 replacement cutter, so spare irons are easy to source. For a single plane that will smooth drawer sides, fit doors, and clean up edges, this is the specification sheet to beat in the budget-to-mid-range tier, and the plane this guide recommends first for new users.
Specs:
- Type: No. 4 bench (smoothing) plane
- Base: Gray cast iron, epoxy coated, precision-ground sides and bottom
- Cutter: 2-inch hardened, tempered steel
- Lever cap: Quick-release cam lock
- Length: 9-3/4 inches
- Weight: Approximately 2.75 pounds
- Handles: High-impact polymer tote and knob
- Replacement cutter: Stanley 12-313
Stanley No. 9-1/2 Block Plane (12-138) — Best Block Plane
A block plane is the hand plane most woodworkers reach for daily, and the Stanley 12-138 is the standard-angle pattern with the features that matter: an adjustable mouth, plus depth and lateral adjustment for the cutter. The cast-iron body is 6 inches long with a 1-5/8-inch cutter bedded at 20 degrees, a geometry aimed at trimming end grain, easing edges, and flushing proud joinery.
The adjustable mouth is the specification to note. Closing it down supports the fibers in front of the cutter for fine work on end grain and tricky stock, while opening it clears thicker shavings during fast trimming. The low, one-handed profile fits an apron pocket, and the finger rest at the front of the body adds control on small parts. Paired with a No. 4 or No. 5 bench plane, the 12-138 covers the small, frequent jobs: chamfering, fitting tenons, trimming veneer, and cleaning up dovetail pins.
Specs:
- Type: Standard-angle block plane
- Length: 6 inches
- Cutter: 1-5/8 inches wide
- Bed angle: 20 degrees
- Mouth: Adjustable
- Adjustments: Depth and lateral
- Body: Cast iron
Stanley Sweetheart No. 4 Smoothing Plane (12-136) — Premium Smoother
The Sweetheart No. 4 is Stanley’s premium take on the smoothing plane. The iron is extra-thick A2 steel at 1/8 inch, which resists chatter and holds an edge longer than the thinner irons in budget planes. The base and frog are cast as one piece, a design Stanley uses to keep the iron seated firmly and to improve accuracy, and the cast-iron base is precision machined. Cherry wood handles replace the polymer grips of the standard line.
Stanley’s catalog lists the 12-136 at 10-5/8 inches overall with a 2-1/2-inch body width and the same 2-inch cutter width as other No. 4 planes, so it fits standard replacement irons and sharpening setups. A locking lateral adjustment helps the iron stay square once set. This is the pick for woodworkers who smooth figured grain regularly and want the heavier iron and one-piece frog in the most versatile bench plane size.
Specs:
- Type: No. 4 smoothing bench plane
- Iron: 2 inches wide, 1/8-inch thick A2 steel
- Base and frog: One-piece cast iron construction
- Overall length: 10-5/8 inches
- Body width: 2-1/2 inches
- Handles: Cherry wood tote and knob
- Adjustment: Depth and lateral, with locking lateral lever
Stanley No. 62 Low Angle Jack Plane (12-137) — Premium Low-Angle Jack
The No. 62 is a bevel-up jack plane: the iron sits bevel-up on a 12-degree bed, so the effective cutting angle is set by the bevel you hone on the blade. Stanley builds this Sweetheart version with a one-piece base and frog, an adjustable throat plate for controlling the mouth opening, and a thick 3/16-inch A2 steel iron that is 2 inches wide. The sole is 14 inches long, and the plane weighs about 6.3 pounds, giving it the mass to push through end grain.
That combination of length, mass, and a low cutting angle is why the No. 62 pattern is favored for shooting board ends, flattening panels, and smoothing stock that tears out under a standard bench plane. Swapping in a spare iron honed at a steeper bevel raises the cutting angle for figured grain, which makes one body cover several jobs. Cherry handles and a machined base round out the specification.
Specs:
- Type: Low-angle jack plane, bevel-up
- Sole length: 14 inches
- Iron: 2 inches wide, 3/16-inch thick A2 steel
- Bed angle: 12 degrees
- Base and frog: One-piece cast iron construction
- Mouth: Adjustable throat plate
- Handles: Cherry wood tote and knob
- Weight: Approximately 6.3 pounds
- Replacement iron: Stanley 12-142
How to choose
Start with sole length, because the numbering system is really a size system. A No. 4, at roughly 9-3/4 inches, is a smoother meant for final passes on stock that is already flat. A No. 5 jack plane, at 14 inches, bridges the gap: long enough to flatten moderate boards, short enough to smooth them. A block plane, around 6 inches, is a one-handed trimming tool.
Next, look at the iron. Standard bench planes use a bevel-down iron on a 45-degree frog, and thicker irons in A2 or O1 steel hold an edge longer and resist chatter better than thin stock irons. Low-angle planes such as the No. 62 use a bevel-up iron on a 12-degree bed, so the cutting angle changes with the bevel you hone, which suits end grain and figured wood.
Then check the mouth and the adjustments. An adjustable mouth or throat plate lets you close the opening for fine work, and depth plus lateral adjustment should move smoothly and stay put. Finally, weigh body material and handles: cast or ductile iron adds useful mass, ground soles reduce setup time, and wood handles feel better over long sessions than hard plastic. Every plane needs sharpening gear, so factor in a stone or honing guide.
Who should skip
Skip hand planes if your work is mostly dimensioning rough lumber to thickness: a benchtop thickness planer removes material far faster, and a hand plane is the wrong tool for stock removal. Skip them, too, if you are not willing to sharpen. Every plane iron needs regular honing, and a dull iron makes any plane frustrating to use.
Woodworkers who mainly build from sheet goods will get limited use from bench planes, since plywood and MDF edges are usually trimmed with a saw or router. And if your main goal is jointing the edges of long boards for panel glue-ups, none of these five is the right pattern: that job calls for a No. 7 or No. 8 jointer plane with a much longer sole. These five are built for smoothing, trimming, and fitting work.
FAQ
What size hand plane should a beginner buy first?
A No. 4 smoothing plane or a No. 5 jack plane is the standard starting point. The No. 4 suits final smoothing and smaller work, while the No. 5 handles flattening and general bench tasks. Most beginners pair one of them with a block plane such as the 12-138 for trimming and end grain.
What is the difference between a bench plane and a block plane?
Bench planes are two-handed tools with the iron held bevel-down on a frog, sized by number from small smoothers to long jointers. Block planes are compact one-handed tools with a bevel-up iron bedded at a low angle and no frog, designed for end grain, chamfers, and small trimming jobs.
Do hand planes need sharpening before the first use?
In most cases, yes. Manufacturers ship irons with a ground bevel that still needs honing to a polished edge before the plane will take fine shavings. Budget planes may also need the sole checked and the iron’s back flattened. Plan on a fine waterstone or diamond plate and a honing guide.
What do the plane numbers mean?
The numbers come from Stanley’s sizing system and roughly follow sole length: a No. 4 is a short smoothing plane, a No. 5 is a mid-length jack plane, and larger numbers get longer. The No. 62 is a separate low-angle jack pattern, and block planes carry their own numbers, such as the 9-1/2.
Final verdict
For most benches, the Stanley No. 4 (12-404) is the right first hand plane: standard dimensions, a ground cast-iron sole, and a widely available replacement cutter. The Amazon Basics No. 4 covers the same jobs for less money if you accept extra setup time. Add the Stanley 12-138 block plane for daily trimming, and choose between the Sweetheart No. 4 and the No. 62 low-angle jack when ready for a premium iron and heavier casting.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.

Write Your Review
No reviews yet. Be the first to share your experience!